Pharmaceutics · Short notes

Solutions, Solubility and Buffers: Short Notes & Cheat Sheet

Physical Pharmacy I: concentration terms, colligative properties, solubility and what changes it, pKa, the Henderson–Hasselbalch equation and buffer capacity.

Short notes

Read these before you attempt the topic's MCQs.

Pharmacopoeial solubility terms

parts of solvent for 1 part soluteVery soluble< 1Freely soluble1–10Soluble10–30Sparingly30–100Slightly100–1,000Practicallyinsoluble> 10,000
Each step to the right needs roughly ten times more solvent to dissolve one part of the drug.

Solutions and concentration

  • Molarity is moles of solute per litre of solution; molality is moles per kilogram of solvent, so molality does not change with temperature.
  • Normality is gram-equivalents per litre; mole fraction is moles of one component over total moles; % w/v is grams per 100 mL.
  • An ideal solution obeys Raoult's law: the vapour pressure of each component equals its mole fraction times the pure vapour pressure.
  • Weak solute–solvent attraction gives positive deviation (ethanol–water); strong attraction gives negative deviation (chloroform–acetone).

Colligative properties

  • They depend on the number of dissolved particles, not their nature: vapour pressure lowering, boiling point elevation, freezing point depression and osmotic pressure.
  • ΔTf = Kf × m, with Kf for water 1.86 °C kg/mol. Blood and tears freeze at −0.52 °C, which is the basis of isotonicity calculations.
  • Osmotic pressure follows van 't Hoff: π = iCRT. The factor i counts particles per formula unit (about 1.8 for NaCl in practice, not a full 2).
  • Osmotic pressure is the most sensitive colligative property, so it is used to find molecular weights of polymers and proteins.

Solubility

  • Pharmacopoeial terms are based on parts of solvent needed for one part of solute (see the cheat sheet).
  • Solubility rises with temperature when dissolving absorbs heat (most solids), and falls when it releases heat (calcium hydroxide, many gases).
  • Smaller particles, metastable polymorphs and amorphous forms dissolve more; cosolvents, surfactant micelles, complexation and salt formation all raise solubility.
  • The common-ion effect lowers the solubility of a sparingly soluble salt.
  • Noyes–Whitney: dissolution rate = DA(Cs − C)/h, so rate rises with surface area A and falls with diffusion layer thickness h.

pH, pKa and buffers

  • Henderson–Hasselbalch for a weak acid: pH = pKa + log([A⁻]/[HA]); for a weak base: pH = pKa + log([B]/[BH⁺]).
  • A weak acid is mostly unionised when pH is below its pKa; a weak base is mostly unionised when pH is above its pKa.
  • A buffer resists pH change. Buffer capacity β = ΔB/ΔpH (Van Slyke) and is greatest when pH = pKa; the useful range is pKa ± 1.
  • Blood is buffered mainly by bicarbonate/carbonic acid (pKa 6.1); at pH 7.4 the ratio of HCO₃⁻ to H₂CO₃ is 20:1.
  • Phosphate, citrate and acetate buffers are common in formulations; borate buffers are kept to eye and external use because of toxicity.

Cheat sheet

High-yield facts in one place. Cover the right-hand column and test yourself.

Solubility terms (parts of solvent per 1 part solute)

TermParts of solvent
Very solubleLess than 1
Freely soluble1 to 10
Soluble10 to 30
Sparingly soluble30 to 100
Slightly soluble100 to 1,000
Very slightly soluble1,000 to 10,000
Practically insolubleMore than 10,000

Key equations

EquationForm
Freezing point depressionΔTf = Kf × m
Osmotic pressureπ = iCRT
Henderson–Hasselbalch (acid)pH = pKa + log [A⁻]/[HA]
Buffer capacityβ = ΔB / ΔpH
Noyes–WhitneydC/dt = DA(Cs − C)/h
Raoult's lawP = x × P°

Memory aids

Like stays neutral in like
Acids stay unionised in acid (pH below pKa) and bases stay unionised in base (pH above pKa).

Exam traps

  • Colligative properties depend on how many particles are dissolved, not on what they are.
  • Buffer capacity is greatest at pH = pKa, not at pH 7.
  • Molality, not molarity, is independent of temperature.
  • A metastable polymorph is more soluble but less stable than the stable form.

Revised? Now test yourself.

Attempt the Solutions, Solubility and Buffers MCQs while the notes are fresh. Anything you get wrong is saved to your incorrect list for the next revision round.

More Pharmaceutics notes